Autumn Endurance-Interseries Proxy Builds

Brumos RSR · 18th-Jun-22, 05:39 AM

Started performing more work on this one as it was found to be tippy. Weight has been pulled from the roof. A duck tail spoiler added and more weight will go down low along with a motor change from the yellow slot it motor to a raptor motor. Then to find a track to tune on as I’ve always wanted to run a MRRC 911S in a proxy. We will see.

Makem · 18th-Jun-22, 08:10 AM

My two, Cunnigham C4R & Lola T260. These have been built for a while.
I have since added a front spolier to the Lola and will change the wheels and tyres to fit the Proxy Regulations.
Will no doubt perform in my usual fashion and hold on to a steady last place Talking

Graham · 18th-Jun-22, 08:42 AM

(18th-Jun-22, 05:39 AM)Brumos RSR Wrote: Started performing more work on this one as it was found to be tippy. Weight has been pulled from the roof. A duck tail spoiler added and more weight will go down low along with a motor change from the yellow slot it motor to a raptor motor. Then to find a track to tune on as I’ve always wanted to run a MRRC 911S in a proxy. We will see.

Looks like you could be running a "Works Team Porsche" entry then with the 904, and both Silver.....great looking.

Graham · 18th-Jun-22, 08:43 AM

(18th-Jun-22, 08:10 AM)Makem Wrote: My two, Cunnigham C4R & Lola T260. These have been built for a while.
I have since added a front spolier to the Lola and will change the wheels and tyres to fit the Proxy Regulations.
Will no doubt perform in my usual fashion and hold on to a steady last place

That Lola looks like a mean machine, could be your Teams secret weapon, but I would probably leave off the front wing for the competition, might be abit too delicate.

Makem · 18th-Jun-22, 05:44 PM

Front spoiler is well glued on to two supports, should be OK. But if it comes off, "C'est la vie".

Brumos RSR · 19th-Jun-22, 12:28 AM

Started working on this one last night, not sure if it will meet the ride height minimum without a few changes. This is a body from Munter and rides on a Dennis Samson chassis.

Kevan · 19th-Jun-22, 10:10 AM

A Porsche saloon! Wavegreen

OXO cube · 19th-Jun-22, 10:56 AM

Denis showcased this on Gregs zoom and it looked great Thumbup

i have the same 510 resin kit from Munter
my brass chassis attempts will never be in Denis's league , therefore mine is a 3DP chassis , so very different
which livery will you use , mine will be BRE when i eventually get around to it ( so many builds )
you might have just spurred me on , to finish up the paint and decals

Kev

Brumos RSR · 19th-Jun-22, 01:29 PM

(19th-Jun-22, 10:56 AM)OXO cube Wrote: Denis showcased this on Gregs zoom and it looked great
i have the same 510 resin kit from Munter
my brass chassis attempts will never be in Denis's league , therefore mine is a 3DP chassis , so very different
which livery will you use , mine will be BRE when i eventually get around to it ( so many builds )
you might have just spurred me on , to finish up the paint and decals

Kev

Mine maybe blue across the hood or BRE livery with the #33.

Brumos RSR · 19th-Jun-22, 01:30 PM

(19th-Jun-22, 10:10 AM)Kevan Wrote: A Porsche saloon!

Definitely as close as you could get I assume back then.