I have been playing with Tinkercad ... would this print OK ?

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

I have been playing with Tinkercad ... would this print OK ?

chappyman66
Senior Member

Posts: 195
Threads: 5
Likes Received: 246 in 119 posts
Likes Given: 555
Joined: Dec 2021
Location MN, USA

#16

9th-May-23, 04:16 AM

Welcome to the rabbit hole....we like it here!

The Benchy looks pretty good. I find the outline peels pretty well once everything cools down and you flex the plate. Also, after several prints it will start to loosen up.

Don't write off bodies....there are ways.

Quote

« Next Oldest | Next Newest »

Messages In This Thread

I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 03:27 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 6th-May-23, 04:37 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 05:47 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 05:58 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 09:09 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 09:55 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 02:55 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 7th-May-23, 04:14 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 04:59 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 7th-May-23, 07:34 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 05:57 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 06:46 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:01 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 08:41 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:52 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 9th-May-23, 04:16 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 08:07 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 10:12 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by OXO cube - 9th-May-23, 10:35 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 11:11 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 12:33 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 12:20 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 12:25 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 01:35 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 01:53 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 9th-May-23, 10:35 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 10th-May-23, 06:04 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 10th-May-23, 06:56 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 10th-May-23, 02:22 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 12th-May-23, 05:13 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 12th-May-23, 05:54 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 13th-May-23, 12:40 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 08:21 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 13th-May-23, 11:48 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 02:39 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 09:48 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 14th-May-23, 05:42 PM

Possibly Related Threads...

Thread / Author Replies Views Last Post

resin print request

719

Last Post by Kevan
4th-Jan-26, 08:33 PM

FDM Print Bed Sheets

1,394

Last Post by MrFlippant
13th-Aug-22, 10:05 PM

The best all round FDM print surface you've probably not heard of...

977

Last Post by Kevan
13th-Nov-21, 01:30 AM

What surface to 3D print on...GRP???

2,273

Last Post by Kevan
24th-Oct-21, 11:40 AM

My first 3dp print

23,532

Last Post by AlexisGaitanis
14th-Mar-20, 09:01 PM

View a Printable Version

Forum Jump:

Users browsing this thread: 1 Guest(s)