1. SlotRacer Forum
  2. 3D Printing
  3. 3DP
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Thread Modes
I have been playing with Tinkercad ... would this print OK ?
Savage GT
Posting Freak
Posts: 984
Threads: 112
Likes Received: 1,307 in 493 posts
Likes Given: 1,247
Joined: Apr 2019
Location Cambridgeshire
#11

8th-May-23, 05:57 PM
You Tube vids on setup watched, bed leveled and tested until within 0.1mm First test print is underway (provided little boat, using provided white PLA), wish me luck !
About 1h 45mins to go according to the screen.
(This post was last modified: 8th-May-23, 05:59 PM by Savage GT.)
[+] 1 member Likes Savage GT's post
Find
Quote
« Next Oldest | Next Newest »


Messages In This Thread
I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 03:27 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 6th-May-23, 04:37 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 05:47 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 05:58 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 09:09 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 09:55 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 02:55 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 7th-May-23, 04:14 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 04:59 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 7th-May-23, 07:34 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 05:57 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 06:46 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:01 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 08:41 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:52 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 9th-May-23, 04:16 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 08:07 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 10:12 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by OXO cube - 9th-May-23, 10:35 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 11:11 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 12:33 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 12:20 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 12:25 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 01:35 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 01:53 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 9th-May-23, 10:35 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 10th-May-23, 06:04 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 10th-May-23, 06:56 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 10th-May-23, 02:22 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 12th-May-23, 05:13 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 12th-May-23, 05:54 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 13th-May-23, 12:40 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 08:21 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 13th-May-23, 11:48 AM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 02:39 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 09:48 PM
RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 14th-May-23, 05:42 PM

Possibly Related Threads...
Thread / Author Replies Views Last Post
resin print request
OXO cube
Last Post by Kevan
4th-Jan-26, 08:33 PM
FDM Print Bed Sheets
Kevan
Last Post by MrFlippant
13th-Aug-22, 10:05 PM
The best all round FDM print surface you've probably not heard of...
Kevan
Last Post by Kevan
13th-Nov-21, 01:30 AM
What surface to 3D print on...GRP???
Kevan
Last Post by Kevan
24th-Oct-21, 11:40 AM
My first 3dp print
AlexisGaitanis
Last Post by AlexisGaitanis
14th-Mar-20, 09:01 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)