Flying Fiona 1929 Fiat - Printable Version

Flying Fiona 1929 Fiat - Printable Version

+- SlotRacer Forum (https://slotracer.online/community)
+-- Forum: Slot Cars (https://slotracer.online/community/forumdisplay.php?fid=3)
+--- Forum: Scratch Building (https://slotracer.online/community/forumdisplay.php?fid=35)
+--- Thread: Flying Fiona 1929 Fiat (/showthread.php?tid=3927)

Pages: 1 2 3 4 5 6

RE: Flying Fiona 1929 Fiat - Kevan - 4th-Jun-24

I just saw this on FB.

What kind of tools do you use for carving etc?

RE: Flying Fiona 1929 Fiat - Tibbs - 5th-Jun-24

Hi Kev,

I use a dremel, different grade sand paper modelers sticks and I have a type of plane which I think is for jib board. It's more like a cheese grater.
I just take small bits at a time as it's easier to remove than put back.

RE: Flying Fiona 1929 Fiat - Kevan - 5th-Jun-24

How do you hack the inside out of a block of wood?

RE: Flying Fiona 1929 Fiat - Tibbs - 5th-Jun-24

With the Dremel Kev, I just go slowly as I don't want to go through the sides but I will go all the way through the bottom

RE: Flying Fiona 1929 Fiat - Kevan - 5th-Jun-24

With a burr?

RE: Flying Fiona 1929 Fiat - Gordon Steadman - 6th-Jun-24

(5th-Jun-24, 04:29 PM)Tibbs Wrote: With the Dremel Kev, I just go slowly as I don't want to go through the sides but I will go all the way through the bottom

You're a lucky man. I've been through loads of Dremels (regular burn out or switch failure) until I saw the light and bought a cheap Chinese knock off that has been perfectly reliable and has a huge selection of cutters. (Probably made in the same factory!) Dremel tools are stupidly expensive and even balsa will blunt them if they are used regularly.

I drill out the bottom and the use the rotary to join the dots and thickness the edges. Good to see your work. The metalwork is superb.

RE: Flying Fiona 1929 Fiat - Tibbs - 6th-Jun-24

(5th-Jun-24, 06:08 PM)Kevan Wrote: With a burr?

[attachment=35767]

RE: Flying Fiona 1929 Fiat - Tibbs - 6th-Jun-24

(6th-Jun-24, 05:57 AM)Gordon Steadman Wrote:
(5th-Jun-24, 04:29 PM)Tibbs Wrote: With the Dremel Kev, I just go slowly as I don't want to go through the sides but I will go all the way through the bottom

You're a lucky man. I've been through loads of Dremels (regular burn out or switch failure) until I saw the light and bought a cheap Chinese knock off that has been perfectly reliable and has a huge selection of cutters. (Probably made in the same factory!) Dremel tools are stupidly expensive and even balsa will blunt them if they are used regularly.

I drill out the bottom and the use the rotary to join the dots and thickness the edges. Good to see your work. The metalwork is superb.

Thanks re work Gordon, really appreciate it.

I brought the Dremel because I was sick of the cheap ones I was buying from Lidls just not man enough and a lot of movement in the headstock. The Dremel doesn't move..
The difference in quality of this Dremel compared to the cheap ones is night and day in my opinion.
Thanks for the tip of drilling out, I'm going to try that. Thumbup

RE: Flying Fiona 1929 Fiat - Kevan - 16th-Oct-24

Did you get this finished Tony?

RE: Flying Fiona 1929 Fiat - Tibbs - 16th-Oct-24

(16th-Oct-24, 07:38 AM)Kevan Wrote: Did you get this finished Tony?

Hi Kevin,
no mate, I'm still on it.
I just decided to start the Ferrari project to refresh my head and get some mojo back.
I'll get back on to the Fiat soon a I love that car.
Cheers