3DP Pods - Printable Version

3DP Pods - Printable Version

+- SlotRacer Forum (https://slotracer.online/community)
+-- Forum: 3D Printing (https://slotracer.online/community/forumdisplay.php?fid=56)
+--- Forum: 3DP (https://slotracer.online/community/forumdisplay.php?fid=57)
+--- Thread: 3DP Pods (/showthread.php?tid=3104)

Pages: 1 2 3 4 5

RE: 3DP Pods - Kevan - 8th-Jul-22

(8th-Jul-22, 08:27 AM)Kevan Wrote:
(8th-Jul-22, 06:15 AM)Savage GT Wrote: Hi Kevan, what offset range does the pod cover ?

I don't actually know, my guess is 1.5mm but I'll fire up the CAD and measure...

'Offset' with motor fully down, axle fully up is 1.25mm, It's more than sufficient for the car it's fitted in and the adjustable height worked perfectly to raise the axle to lose excess ground clearance.

RE: 3DP Pods - Kevan - 8th-Jul-22

I've quickly tweaked the offset slot and it's now 1.5mm

RE: 3DP Pods - Kevan - 8th-Jul-22

Tonight I'm working on a FF050 (Slimline) pod with a twist...a 90° twist...to allow room for ballast either side of the motor.

[attachment=24789]

[attachment=24790]

RE: 3DP Pods - OXO cube - 9th-Jul-22

a slim can adaptor for a slot.it type inline pod would be useful
that way you would have your 3 inline pod types , one for each motor
and adaptors for each motor type to suit the original slot.it inline pod
best of both worlds
are you up for the challenge Kevan ? Bigsmile

Kev

RE: 3DP Pods - Kevan - 9th-Jul-22

I made one last year, the problem is the fixing screws.

RE: 3DP Pods - Savage GT - 9th-Jul-22

(9th-Jul-22, 06:30 AM)OXO cube Wrote: a slim can adaptor for a slot.it type inline pod would be useful
that way you would have your 3 inline pod types , one for each motor
and adaptors for each motor type to suit the original slot.it inline pod
best of both worlds
are you up for the challenge Kevan ?

Kev

Scaleauto do a motor mount for slimline that has the same mountings as Slot.it pods ...

If you want a challenge Kevan, 2x slimline motors side by side in a small angle v (just enough to clear the pod siderails) configuration in a pod that fits standard slot.it mountings with a 0.5mm offset (in relation to standard inline pods) Rofl

mind you, I dont know your location so if its the U.S the postage would kill me Tappingfoot

Likewise, less challenging is AW long can/AW short can/SW and Inlines with a 2mm offset. This would allow using more scale accurate (ie larger) wheels/tyres and not have 4x4 ground clearances Wrench

RE: 3DP Pods - AlexisGaitanis - 9th-Jul-22

(9th-Jul-22, 06:30 AM)OXO cube Wrote: a slim can adaptor for a slot.it type inline pod would be useful
that way you would have your 3 inline pod types , one for each motor
and adaptors for each motor type to suit the original slot.it inline pod
best of both worlds
are you up for the challenge Kevan ?

Is this you are looking for?[attachment=24791]

RE: 3DP Pods - OXO cube - 10th-Jul-22

Scaleauto do a motor mount for slimline that has the same mountings as Slot.it pods

thanks Savage GT .... wasnt aware of this Thumbup

yes AlexisGaitanis thats exactly it Thumbup

RE: 3DP Pods - AlexisGaitanis - 10th-Jul-22

I make them both,they accept Slot.it spherical bushing and have adjustable ride height

RE: 3DP Pods - Kevan - 10th-Jul-22

Is that a 612 CanAm?

[attachment=24808]